Before You Ride
Free Performance Updates
IMPORTANT: Performance updates may be available for your new e-scooter. To get the best possible performance out of your brand-new e-scooter, just download the Pure app, connect it to your scooter, and go to the Scooter Update tab. Check the app regularly for new updates.
DOWNLOAD THE APPTyre Pressure and Battery Range
Use the tyre valve extender and pump included in the box to inflate your tyres to the required pressure of 36psi and make sure you fully charge your e-scooter by waiting for the light on your charger block to go from red to green. PLEASE NOTE: This is because your battery might have reduced range, since it’s so brand new and may never have been used. It’s totally normal and shouldn’t be an issue after your scooter’s been through a full charge and discharge cycle.
Key Safety Checks:
Unboxing Your New E-Scooter
Step By Step
![](http://au.pureelectric.com/cdn/shop/files/1-raise-stem.png?v=1710935637&width=1)
1. Raise the stem
Remove the protective packaging but do not lift the scooter out of the cardboard frame just yet. Lift the stem until it clips upright into the frame.
![](http://au.pureelectric.com/cdn/shop/files/2-secure-latch.png?v=1710935637&width=1)
2. Secure the latch
Lift the latch mechanism until it clips securely into the stem. Warning! Do not ride the scooter if the latch is loose.
![](http://au.pureelectric.com/cdn/shop/files/unfold-handlebars.png?v=1710935636&width=1)
3. Unfold the handlebars
Take the right handlebar. Pinch and slide the 2 toggles (one on the front and one on the back) atthe same time to unfold the handlebar. Raise the handlebar into the riding position. Repeat the steps for the left handlebar.
![](http://au.pureelectric.com/cdn/shop/files/secure-handlebars.png?v=1710935629&width=1)
4. Secure the handlebars
Once each handlebar is in the riding position, check they are securely in place. Do not ridethe scooter if the handlebar is loose.
![](http://au.pureelectric.com/cdn/shop/files/charge-battery.png?v=1710935629&width=1)
5. Charge the battery
You can charge your e-scooter by plugging the charging cable into the charging port. Once fully charged the charger light will change from red to green.
![](http://au.pureelectric.com/cdn/shop/files/6-prepare-for-riding.png?v=1710935637&width=1)
6. Prepare the scooter for riding
Lift the scooter out of the cardboard holder and bring down the central kickstand to stabilise the scooter. Bring down the footpads.
![](http://au.pureelectric.com/cdn/shop/files/7-check-tyre-pressure.png?v=1710935638&width=1)
7. Check your tyre pressure
Use the tyre valve extender and pump included in the box to inflate your tyres to the required pressure of 36psi. IMPORTANT: Always use the tyre valve extender provided every time you attach the pump to your tyres, or you risk breaking the valve.
Quick Tips To Get Going
![](http://au.pureelectric.com/cdn/shop/files/1-qs-advance-control.png?v=1710935638&width=1)
1. The Controls
Use your right thumb to operate the throttle and your left hand for the brake and indicators.
![](http://au.pureelectric.com/cdn/shop/files/2-qs-select-mode.png?v=1710935638&width=1)
2. Select Mode
Switch on and double press the multifunction button to select your riding mode.
![](http://au.pureelectric.com/cdn/shop/files/3-qs-set-off.png?v=1710935638&width=1)
3. Push To Start
Simply push off the ground, then press the throttle to activate the motor.
Safety Information
- Choosing a selection results in a full page refresh.